Rixson 27 Floor Closer vs Norton 1601 on a Heavy Door

Rixson 27 Floor Closer vs Norton 1601 on a Heavy Door

Posted by Kent on 17th Nov 2026

Where the door's weight goes

A door closer has two jobs: swing the door shut and control how it gets there. The part people skip is the third job, carrying the door. On a surface closer mounted on the frame, the hinges carry the weight and the closer just pushes. On a floor closer, the closer carries the weight itself. That is the real difference between a Norton 1601 and a Rixson 27, and it decides which one belongs on a heavy exterior door.

We stock both. The Rixson 27-180N-LH-606, 27-85N-LH-613 and 27-180A-LH-605 are offset hung floor closers. The Norton 1601-691 is a surface-mounted closer. Here is what the listings say and what I would pick.

The numbers from the listings

Rixson 27 seriesNorton 1601
Mounting3/4" offset hung, in the floorSurface mounted: regular arm, top jamb or parallel arm
Door weightTo 450 lbsNot stated in the listing
Door widthUp to 4 feetAdjustable size 1 thru 6
StandardANSI/BHMA A156.4ANSI/BHMA Grade 1
BodyFloor unit, non fire ratedCast aluminum body
Example27-180N-LH-6061601-691

The Rixson 27: the floor carries the door

The listing says the weight of the door is supported by the bottom arm and floor, which makes it ideal for single acting exterior or interior doors. It is rated to 450 lbs on a door up to 4 feet wide, using the proper number of intermediate pivots. The same listing calls it a heavy duty 3/4 inch offset hung closer, left handed in the examples here, single acting.

That matters on a heavy glass or solid wood door. If a door weighs three hundred pounds, hinges alone will sag over time. The floor closer takes the load off them. It is also hidden. Nobody sees an arm on the top of a lobby door.

But a floor closer is an install, not a swap. It sits in a cement box in the floor under the door. If you already have a floor closer, replacing it is simple. If you do not, you are cutting concrete. That is the cost of choosing a floor closer, and it should be made with your eyes open.

Three Rixson variants, three behaviors

  • 27-180N: non hold-open, adjustable hydraulic backcheck, opens to 180 degrees. The listing recommends an auxiliary floor or wall stop at the full opening.
  • 27-85N: a built-in positive dead stop that prevents the door from swinging past 85 degrees. This is the one for a door that opens into something: a wall, a column, a piece of glass.
  • 27-180A: automatic hold-open, adjustable hydraulic backcheck, 180 degrees. This is the one a kitchen or loading area wants, where the door should stay out of the way.

The N and A in the part number is the difference between "closes by itself" and "holds itself open." Our earlier article covers the 180N and 180A in more depth. If a door is part of a fire-rated opening, ask us before you order, because the 27 series listing says non fire rated.

The Norton 1601: the hinges carry the door

The 1601 is the closer on most commercial doors you walk through. The listing describes a surface-mounted commercial closer with separate latch, sweep and backcheck valves, ANSI/BHMA Grade 1, for exterior or interior doors. It has a cast aluminum body, adjustable size 1 through 6, a 2-7/8 inch projection and a 1-3/8 inch piston. Tri-Style packaging means it mounts as regular arm, top jamb or parallel arm. The dull bronze 1601-691 is non-hold-open.

The advantage is the install. A few screws and an arm, with no concrete. For a standard aluminum storefront door, the listing calls it an ideal fit. The adjustable size is why one box can work on a range of doors: you set the spring power to the door instead of ordering a different closer.

What the 1601 listing does not give is a door weight limit. It gives sizes 1 to 6 but not what each size handles, so I am not going to put a number on it. If your door is heavy, check the manufacturer's size chart for the exact door before you buy, and if the weight is beyond what a surface closer should carry, step up to a floor closer.

How I pick

  • Standard storefront, normal weight: Norton 1601. Easy to install, easy to adjust, easy to replace.
  • Heavy door, up to 450 lbs and 4 feet wide: Rixson 27 floor closer.
  • Door that must not hit the wall: Rixson 27-85N with the dead stop.
  • Door that must stay open: Rixson 27-180A, as long as it is not a rated opening.
  • You will not cut the floor: surface closer, and check the size chart against the door.

The mistakes I fix

The most common one: a surface closer on a door that is too heavy, the arm bent and the door dragging on the threshold. The second: a hold-open closer on a door where hold-open was never wanted, because somebody grabbed the wrong letter. The letter in the part number is the thing to read.

Handing is the third. The Rixson examples here are left handed, so check which way your door swings before you order. A right-hand unit on a left-hand door does not get a refund from physics.

Tell us the door's width, thickness, material and whether it is exterior, and we will confirm the closer. Also see Norton 1600 adjustable closer for a light commercial door.